Show TOC

Example documentationRollup Examples

 

The following examples illustrate common settings for rollup.

The following examples assume operators work on SFC numbers one at a time. If operators work on multiple SFC numbers, the system divides SFC labor according to the setting of the Distribution of SFC Labor Time field in Labor Rule Maintenance. For more information, see Labor Rule Maintenance.

Example 1
Setup

Prerequisites:

  • On the Rollup Processing Rules tab page in Labor Rule Maintenance, you have set the Idle Factor for Labor Time field to Labor on to Labor off.

  • You have created an indirect user LCC in Labor Charge Code (LCC) Maintenance named IDLE_TIME. This is the default user LCC for the operators in this example.

  • You have set up Labor on to run on Start and Labor off to run on Complete in POD Maintenance.

The figure below illustrates Example 1 and is followed by an explanation:

What Operators Do

Production operators clock in at the beginning of the shift, and the system starts charging their time against IDLE_TIME. At the workstation, the operator works one SFC number at a time in the POD. The operator clocks out at the end of the shift without changing his or her user LCC during the shift.

User Labor Results

If you selected the Enable User Labor Summarization checkbox on the Rollup Processing Rules tab in Labor Rule Maintenance, the system logs the following against the user’s default LCC, IDLE_TIME:

  • Time between clock in and the labor on to the first SFC number

  • Time between the labor off from one SFC number and the labor on to another

  • Time between the labor off from the last SFC number and clock out

The system logs the time between the labor on to and labor off from an SFC number against the respective SFC LCC. The system associates this time with the user.

SFC Labor Results

If you selected the Enable SFC Labor Summarization checkbox on the Rollup Processing Rules tab page in Labor Rule Maintenance, the system logs the time between the labor on to and labor on from each SFC number against the SFC LCCs.

Example 2
Setup

Prerequisites:

  • You have set the Idle Factor for Labor Time field to Labor on to Labor on on the Rollup Processing Rules tab page in Labor Rule Maintenance.

  • You have created an indirect user LCC in Labor Charge Code Maintenance named IDLE_TIME, and this is the default user LCC for the operators in this example.

  • You have set up Labor on to run on Start and Labor off to run on Complete in POD Maintenance.

The figure below illustrates Example 2 and is followed by an explanation:

What Operators Do

A production operator clocks in at the beginning of the shift, and the system starts charging time against IDLE_TIME. At the workstation, the operator works one SFC number at a time in the POD. The operator clocks out at the end of the shift without changing the user LCC during the shift.

User Labor Results

If you selected the Enable User Labor Summarization checkbox on the Rollup Processing Rules tab page in Labor Rule Maintenance, the system logs the following against the user’s default LCC, IDLE_TIME:

  • The time between clock in and the labor on to the first SFC number

  • The time between the labor off from the last SFC number and clock out

The system logs the time between the labor off from one SFC number and the labor on to the next SFC number against the previous SFC LCC. The system associates this time with the user.

SFC Labor Results

If you selected the Enable SFC Labor Summarization checkbox on the Rollup Processing Rules tab page in Labor Rule Maintenance, the system logs the total time between the labor on to one SFC number and the labor off from the next SFC number against the first SFC LCC.

Example 3
Setup

Prerequisites

  • On the Rollup Processing Rules tab page in Labor Rule Maintenance, you have set the Idle Factor for Labor Time field to Labor on to Labor off.

  • You have set up Labor Tracking with no clock in required.

  • You have selected the Enable SFC Labor Summarization checkbox, and cleared the Enable User Labor Summarization checkbox on the Rollup Processing Rules tab in Labor Rule Maintenance.

  • You have set up Labor on to run on Start and Labor off to run on Complete in POD Maintenance.

The figure below illustrates Example 3 and is followed by an explanation:

What Operators Do

Without clocking in or clocking out, a production operator works one SFC number at a time in the POD.

User Labor Results

Without clocking in or clocking out, the system does not count user labor results.

SFC Labor Results

The system logs the time between the labor on and labor off to or from each SFC number against the SFC LCCs.