Modify Replication Flow Object Schemas and Settings

You can modify an existing replication flow after it has been created. The changes you can make depend on the current status of the replication flow and the kind of updates you want to make.

Add an Object to a Replication Flow

You can add more objects to an existing replication flow, so that additional data will be replicated going forward:
  1. Open the replication flow in its editor.

  2. Choose (Add source objects).

  3. Select the objects that you want to add.

  4. Choose Add Selection.

  5. Select a Load Type and set other properties as appropriate.

  6. Click Deploy to deploy your changes.

At the next delta interval or scheduled run, the new object will perform an initial load and/or begin tracking changes for future delta loads.

Remove an Object from a Replication Flow

You can remove objects from an existing replication flow, so that data for these objects will no longer be replicated:
  1. Open the replication flow in its editor.

  2. Choose Remove next to the object that you want to remove.

  3. Click Deploy to deploy your changes.

Existing data in the target object remains unchanged.

Add a Column to an Object

You can add columns to an existing replication object. Adding a column to a replication object changes the target schema and will cause any data already replicated to the target object to be deleted and for replication from the source object to start again.
  1. Open the replication flow in its editor.

  2. Add the required column to the target object using the table editor.

  3. Choose Additional Options → Map to Existing Target Object.

  4. Click Deploy to deploy your changes.

Rename a Target Object

You can rename the target object of a replication object:
  1. Open the replication flow in its editor.

  2. Select the replication object that you want to rename.

  3. Choose Rename Target Object.

  4. Enter a new technical name.

  5. [Optional] Select Copy Columns from Source Object.

  6. Click Rename.

  7. Click Deploy to deploy your changes.

Change Delta Load Run Setting

Configure how delta changes are processed for a replication flow. You can choose whether delta processing runs continuously at the configured delta interval or only when triggered by a schedule or task chain.
  1. Open the replication flow in its editor.

  2. Select Edit Run Settings.

  3. Under Delta Load Run, select one of the following options:

    • At Delta Interval: The replication flow runs continuously and queries for delta changes based on the specified delta interval.

    • At Scheduled Time: The replication flow processes the available delta changes and then the run completes. The next run begins at the next scheduled time.

  4. Click Save to confirm your changes.

Review and Apply Schema Changes in SAP ABAP (SLT) Source Objects

You can enable source schema change detection for an existing replication flow that uses an SAP ABAP (SLT) source and a SAP Datasphere (HANA) target to apply supported source schema changes without reinitializing the replication flow.

Schema changes are not applied automatically. To apply supported schema changes:

  1. Open the replication flow in the editor.

  2. Select the affected replication object.

  3. Choose Review Schema Changes.

  4. Review the detected schema changes.

  5. Select the supported changes that you want to apply.

  6. Save and Deploy to apply the selected schema changes.

Change Source and Target Thread Limits

You can change the maximum number of threads that can be used when reading data from the source system:
  1. Open the replication flow in its editor.

  2. Select Edit Run Settings.

  3. Update the Source Thread Limit and Target Thread Limit values.

  4. Save the changes.

  5. Click Deploy to deploy your changes.

Change the Load Type of an Object

You can change the load type of replication objects in a running replication flow:

  1. Open the replication flow in its editor.

  2. Select the replication object whose load type you want to change.

  3. In the properties panel, select the required load type.

  4. Click Deploy to deploy your changes.

Changing the Content Type (ABAP-Based Source Systems Only)

When working with ABAP-based source systems, you can switch between Template Type and Native (See Creating a Replication Flow).

  1. Open the replication flow in its editor.

  2. Change the content type.

    Data Types Native Type Template Type

    Date

    String (length = native content length)

    Date

    Time

    String (length = native content length)

    Time

    Boolean

    String (length = native content length)

    Boolean

    Timestamp

    Decimal (Precision = abapLength, scale = abapDecimals)

    Timestamp

    Raw

    Binary

    String

  3. Review any required data type conversions.

  4. Click Deploy to deploy your changes.

When changing the content type, you must convert some data types to ensure that they are supported by the selected content type: